dimensions are shown in mm dimensions subject to change www.ittcannon.com contacts copper alloy plating contact area : gold alloy inlay or gold over nickel terminals : tin lead (2 min) moldings high temp. thermoplastic ul 94v-0 rated slide lock/metal cover stainless steel number of contacts 6 or 8 mechanical life, hinged cover 10,000 cycles min mechanical life, ?ed cover 50,000 cycles card insertion force hinged cover: 1 n max fixed cover: 3 n max card extraction force hinged cover: 1 n max fixed cover: 0.80 n min / 3 n max contact force 0.25 n min / 0.50 n max slide locking force 2 n min / 6 n max vibration frequency 10 to 500 hz. acceleration 50m/s 2 duration 6 hours - amplitude 0,35 mm max electrical discontinuity 1? shock peak value 500 m/s 2 ?duration 11 ms 3 shocks in each direction of each axis max electrical discontinuity 1 ? insulation resistance 1,000 m ? min resistance 100 m ? max current rating 10 ? min / 1 a max dielectric strength 750 vrms min card detection switch normally open contact resistance 100 m ? max dielectric strength 250 vrms min current rating 1 ma min / 10m a max maximum power 0.2 va operating temperature -40? to +85? soldering temperature temperature/time pro?e acc. to cecc00802 para. 6.1, fig. 3 with peak temperature 250? damp heat iec 512 test number 11c (10 days) salt mist iec 512 test number 11f (96 hours) quantity per reel, see table next page. 19 ccm03 mk ii a new range of ccm03 connectors have been developed to interface with sim/sam cards as de?ed by gsm11- 11 and env1375-1. the connectors are available with either hinged covers or ?ed covers and have been designed to minimize the amount of space needed for pcb mounting. features hinged cover ?available with 6 or 8 contacts, with or without pcb locating pegs. ?available with insulated card presence switch. ?the cover springs open when unlocked while the card is in place. ?the molding is polarized so that the cover can only be closed if the card is correctly inserted. ?the cover can be replaced without removing the connector from the pcb. ?inspection slots allow an electrical test to be made without opening the cover. ?the overall height of the connector is only 2,5 mm. the amount of space needed to mount the connector is just 29,65 mm x 17,2 mm. fixed cover ?available with 6 or 8 contacts. ?the overall height of the connector is 2,85 mm max. only 25,5 mm x 17,2 mm of board space is required to mount the connector. general ?with tape and reel packaging as stan- dard, the connectors are designed to be automatically pick-and-placed. ?the high temperature thermoplastic moldings are suited for infrared and convection soldering processes. ?by using an inlay ?ish in the contact area the life of the precious metal is extended by over 10 times that of standard gold plating. ?robustly formed printed circuit tails allow a co-planarity of 0,05 mm to be maintained. construction mechanical data contact electrical data switch electrical data environmental data packaging
dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings 1,25 1,25 (2,7 max. includes solder tails) 2,5 11,35 17,2 3,81 3,8 3,5 2,45 1,25 5,65 0,2 13,8 29,65 0,1 0 -0,1 0,7 25 ? 0' 0,8 (ref.) 25,5 0,65 r 1,9 3,81 3,81 25,4 0,2 0,4 180 ? max (ref.) 25,5 25 28,4 microsim card xx-xxx see detail a date code area mated condition r 1,9 pick and place area 3,5 slider locked bump detail a pcb layout unless otherwise stated, tolerances are 0,10 mm hinged cover ccm03 - 3001 (6 contacts) 3002 (6 contacts - pcb locating pegs) 3003 (8 contacts) 3004 (8 contacts - pcb locating pegs) ccm03-3001 / 3002 ccm03-3003 / 3004 notes: coplanarity of soldering surfaces: 0,05 mm *pegs: height 0,7 mm and 1 mm 20 ccm03 mk ii part number number of cover pcb locating quantity contact switch card presence contacts pegs per reel finish lock switch ccm03-3001 r102 6 hinged no 1000 inlay no no ccm03-3002 r102 6 hinged yes 1000 inlay no no ccm03-3003 r102 8 hinged no 1000 inlay no no ccm03-3004 r102 8 hinged yes 1000 inlay no no ccm03-3009 r102 6 hinged no 1000 gold no no ccm03-3010 r102 6 hinged yes 1000 gold no no ccm03-3011 r102 8 hinged no 1000 gold no no ccm03-3012 r102 8 hinged yes 1000 gold no no ccm03-3013 r102 6 hinged no 1000 gold no yes (insulated) ccm03-3514 r122 6 hinged no 1200 inlay yes no ordering code ccm03-3504 r122 8 fixed no 1200 inlay no no ccm03-3505 r122 6 fixed no 1200 inlay no no 25,5 2,5 5,5 5,5 3,81 3,81 1,8 1,27 8,6 23,2 1,5 1,5 9,34 6,35 20,32 10,16 5,08 1,2 +0,1 0 0,1 1,44 2x 2,54 1,3 0,2 current location according to env1375-1 & gsm11-11 contact foot area 0,8 x 1 (component side) 6x c5 plastic outline pad prohibited area c6 c7 c1 c2 c3 2x 25,5 2,5 5,5 5,5 3,81 3,81 1,8 1,27 8,6 23,2 1,5 1,5 9,34 1,55 3x 2,54 1,3 0,2 contact location according to env1375-1 & gsm11-11 c5 0,8 x 1 (component side) prohibited area c6 c7 c1 c2 c3 c8 c4 8x plastic outline pad
21 dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings pcb layout unless otherwise stated, tolerances are 0,10 mm hinged cover ccm03 - 3013 (6 contacts + card presence switch) ccm03 - 3013 (6 contacts + card presence switch) note: coplanarity of soldering surfaces: 0,05 mm ccm03 mk ii hinged cover insulated card presence switch 25,5 2,5 5,5 5,5 3,81 3,81 1,8 1,27 8,6 23,2 1,5 1,5 9,34 1,55 3x 2,54 1,3 0,2 contact location according to env1375-1 & gsm11-11 c5 contact foot area 0,8 x 1 (component side) prohibited area c6 c7 c1 c2 c3 sw sw 8x plastic outline pad 1,25 1,25 (2,7 max. includes solder tails) 2,5 11,35 17,2 3,81 3,8 3,5 2,45 1,25 5,65 0,2 13,8 29,65 0,7 25 ? 0' 13,15 2,1 9,6 3,7 0,65 r 1,9 1 0,3 a 0,1 0 -0,1 0,8 25,5 0,2 0,4 (ref.) 25,5 3x 2,54 8,6 1,27 3,81 3,81 25,4 0,2 0,4 180 ? max 25 28,4 15 (ref.) 25,5 microsim card xx-xxx see detail a date code area mated condition 8x detail insulated blade switch r 1,9 pick and place area 3,5 slider locked detail a plastic actuator a
22 dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings 11,35 17,2 3,81 3,8 0,7 1,25 1,25 2,45 3,5 5,65 0,2 13,8 29,65 25 ? 0' 2x 2,54 13,15 0,4 25,5 0,2 1,25 r 1,9 9,6 3,7 2,1 0,65 0,8 (ref.) 25,5 0,6 0,3 a 8,6 1,27 5,08 5,08 (3,2 max includes solder tails) 3 0,5 +0,1 0 0,45 0,1 0 3,81 3,81 0,4 25,4 0,2 180 ? max 28,4 15 (ref.) 25,5 25 microsim card bump xx-xxx see detail a date code area mated condition 8x on contacts & left lock switch terminal on right lock switch terminal only r 1,9 pick and place area 3,5 slider locked left lock switch terminal right lock switch terminal detail a a pcb layout 3,81 3,81 2,5 5,5 5,5 25,5 3 3,4 5,6 7,6 2,4 1,8 1,4 5,08 5,08 1 0,2 23,2 1,5 1,5 1,55 9,34 2x 2,54 8,6 1,27 c5 contact foot area 0,8 x 0,6 (component side) c6 c7 c1 c2 c3 8x contact location according to env1375-1 & gsm11-11 plastic outline pad prohibited area unless otherwise stated, tolerances are 0,10 mm hinged cover ccm03 - 3514 (6 contacts - with switch on metal lock) ccm03 - 3514 (6 contacts - with switch on metal lock) note: coplanarity of soldering surfaces: 0,05 mm ccm03 mk ii hinged cover
23 dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings a a b b (ref.) 3,45 21,55 1,4 +0,05 0 0,15 min 2,45 1,6 1,4 +0,05 0 0,8 30 ? 0' 0,8 1,25 0,05 0,2 2,65 12,1 15,2 +0,1 0 17,2 0,05 1,9 2,3 40 ? 0' (ref.) 25,5 0,75 25,5 0,2 12,7 2,5 3x 2,54 1 0,3 a 10,16 3,81 3,81 0,3 0,02 0,4 2,54 0,1 0 -0,1 8,6 1,27 12,75 25,5 (ref.) 25,5 (ref.) 17,2 (ref.) 9,75 12,9 0,4 2,85 (3 max includes solder tails) date code area card stop mated condition xx-xxx pick and place area 3,5 see detail a 8x detail a a pcb layout unless otherwise stated, tolerances are 0,10 mm fixed cover ccm03 - 3504 (8 contacts) ccm03 - 3505 ccm03 - 3504 note: coplanarity of soldering surfaces: 0,05 mm ccm03 mk ii fixed cover y y y y y y y 2x 1,4 +0,05 0 8,6 6,35 2,54 1,5 23,2 1,5 1,44 3x 2,54 1,27 12,7 1,3 0,2 contact location according to env1375-1 & gsm11-11 c1 c5 contact foot area 0,8 x 1 c2 c3 c4 c6 c7 c8 8x (component side) plastic outline pad prohibited area 2,5 5,5 5,5 1,8 3,81 3,81 25,5 2x 1,4 +0,05 0 8,6 6,35 2,54 1,5 23,2 1,5 1,44 2x 2,54 1,27 1,3 0,2 12,7 env1375-1 & gsm11-11 c1 c5 contact foot area 0,8 x 1 c2 c3 c6 c7 6x (component side) plastic outline pad prohibited area
24 dimensions are shown in mm dimensions subject to change www.ittcannon.com contacts copper alloy contacts ?ish gold over nickel pc tail plating tin lead (2 min) molding high temp. thermoplastic, ul94v-0 cover stainless steel number of contacts 6 mechanical life 10,000 cycles min contact force 0.35 n min / 0.50 n max vibration frequency 10 to 500 hz. acceleration 50m/s 2 duration 6 hours - amplitude 0.35 mm (0.014) max electrical discontinuity 1? insulation resistance 1,000 m ? min resistance 100 m ? max current rating 10 ? min / 1 a max dielectric strength 750 vrms min card detection switch normally open contact resistance 100 m ? max dielectric strength 250 vrms min current rating 1ma min / 10m a max maximum power 0.2 va operating temperature -40? to +85? soldering temperature temperature/time pro?e acc. to cecc00802 para. 6.1, fig. 3 with peak temperature 250? damp heat iec 512 test number 11c (10 days) salt mist iec 512 test number 11f (96 hours) 5 reels per box. ccm03 mk ii with auto lock cover a new range of ccm03 connectors have been developed to interface with sim/sam cards as de?ed by gsm11- 11 and env1375-1. the connectors are available with a hinged metallic cover and have been designed to provide an easier open/lock function and side card entry. features ?available with 6 cross contacts which are designed to give a consistently reliable normal force over the life of the connector. ?the hinged metallic cover can auto- matically lock by pressure. ?side entry of the card ensures easier positioning of the card into the con- nector. ?insulated blade switch version available for detection card when cover is closed. ?the molding is polarized so that the cover can only be closed if the card is correctly inserted. ?inspection slots allow an electrical test to be made without opening the cover. ?with tape and reel packaging as standard, the connectors are designed to be automatically pick-and-placed. ?the moldings are made from high- temperature thermoplastics suited to infrared and convection soldering processes. ?robustly formed printed circuit tails allow a coplanarity of 0,05 mm to be maintained. part number number of cover card presence quantity contacts switch per reel CCM03-3517 6 side hinged no 1300 ccm03-3518 6 front hinged yes (insulated) 1300 ccm03-3529 6 front hinged no 1300 construction mechanical data contact electrical data switch electrical data environmental data ordering code packaging
25 dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings pcb layout unless otherwise stated, tolerances are 0,10 mm hinged cover ccm03 - 3517 (6 contacts) ccm03 - 3517 (6 contacts) note: coplanarity of soldering surfaces: 0,05 mm ccm03 mk ii with auto lock cover 5,5 2,5 5,5 1,8 24,6 16,1 2 11,1 2 2,5 5 3,81 3,81 22,1 1,5 1,5 1,25 8,24 1,4 0,2 8,82 1,27 2x 2,54 contact foot area 1 x 1 (component side) c1 contact location according to env1375-1 & gsm 11-11 c2 c3 c5 c6 c7 6x plastic outline pad prohibited area 8,82 1,27 2x 2,54 12,05 1,3 4,9 17 29,6 29,1 0,25 0,25 0,9 0,9 0,95 0,95 7 2 2,5 max 3,23 8,64 5 1,3 2 max. 0,9 1,85 2,1 max on metal cover 11,61 24,6 0,2 0,25 0,1 +0,05 -0,10 1 24,6 (ref.) 1 0,3 a 2,2 1,8 1,9 14,5 unlocked 1 2 card insertion card insertion onto the base open open card withdrawal manual opening card withdrawal from the base 1 2 locked unlocked locked manual closing 6x pick and place area 3,2 xx-xxx date code area detail a detail a a
26 dimensions are shown in mm dimensions subject to change www.ittcannon.com dimensional drawings max (on insulator) 2,1 2,2 max (on metal cover) 24,6 0,2 11,8 11,8 0,5 5,1 11,17 2,86 1,27 3x 2,54 8,45 1 0,3 a 18 max during opening 4,4 3,2 4,4 0,95 2,3 17 10,5 2,4 29,65 0,1 +0,05 -0,1 1 (ref.) 24,6 25,2 2,8 locked 8x pick and place area 3,2 date code area see detail a detail a insulated blade switch plastic actuator blade switch unlocked unlocked open manual opening card withdrawal from the base 2 1 open open card insertion onto the base 1 2 manual closing locked 2 a pcb layout 24,6 1,8 2x 2 2,5 5,5 5,5 5 1,05 19,1 1,4 0,2 8,45 1,27 3x 2,54 22,1 1,5 1,5 3,81 3,81 7,24 1,7 contact foot area 1 x 1 prohibited area (component side) c1 c5 c2 c3 sw c6 c7 sw contact location according to env1375-1 & gsm 11-11 pad plastic outline 8x card withdrawal card insertion unless otherwise stated, tolerances are 0,10 mm hinged cover ccm03 - 3518 (6 contacts and switch) ccm03 - 3518 (6 contacts and switch) ccm03-3529 (without switch) layout is similar except sw pads note: coplanarity of soldering surfaces: 0,05 mm ccm03 mk ii with auto lock cover
|
